Hi all,

I have a GO7 13" in a pac man mini and im getting a lot of curling on the right edge of the screen. is this just in need of a new cap kit or is it something else. any help would be appreciated.

http://www.youtube.com/watch?v=YqmH4RYZTWI&feature=youtu.be

dose anyone know where i can get replacement ram for my ms pac board. im not getting any sound and just load hum and speaker popping, i saw online that you should replace the 2l and 2k ram

well i dont have a cabinet, im using a monitor that doesn't need an isolation transformer, i picked up the board for 20 bucks, not working but its missing an eprom which might be an issue. i want to get it working, so i bought a harness from bob. im pretty much just setting up a test station with it right now. Thanks.

john, if i use the switcher to power ms pac do i still need the fuse blocks.

Hey guys i was hoping someone could help me out, im wiring a ms pacman board to a switcher power supply. ive noticed that there's 7 pin outs for +5volt, do i just piggy back all of them on the one +5volt terminal

thanks

no where is it

the eproms are not listed in the device list, you can use a general 24 pin like a 2716 or 2732 but its not matching the roms from romident, the checksum is all wrong.

yeah, is it it on ebay, its a little pricey but it looks like it supports a hell of a lot more roms then the one i got. might have to bite the bullet and buy it. i just dont understand i though the 2532's were the most common

looks like there are a lot of roms that are not supported by the genius g540 universal programer. i cant believe it doesn't support the roms from ms pac man (HN462532G). i can get them to read using other rom settings but they don't read the whole thing i guess. can anyone suggest a good eprom programer that supports most of these devises.

Hey Guys,

I've got a technical question and i was wondering if anyone could help me out. I just picked up what i think is a bootleg pac man or ms pac man board off ebay for a few bucks the board is labeled pac-3. I removed a rom and tried to match it against hamsters online rom ident but im having a problem. the rom reads fine but when i save it to compare it to the data base it doesn't recognize the rom. i figured it was probably a bad rom but i took one off a working ms pac man board and when i saved it and compared it to the data base it still doesn't recognize it. when im saving the rom ive saved it as both a hex file and a bin and still no luck. can anyone tell me what im doing wrong? i am using a genius g540 programer. any help with this would be appreciated...

I came accross this on craigs list and facebook

Entertainment Auction Company of New England
https://m.facebook.com/EACbids?id=738589272836679&refsrc=http%3A%2F%2Fwww.google.com%2F&_rdr

Anybody know anything about it and are planning on going?

Tryed that, when i turn off the game and then back on again the pictures great. Then after a while it loses the hold. Didnt mess with the pots on the pcb though. Ill try again tonight when i get home to fine tune. The thing is my power supplys been a little flacky. I got a new one but i didnt like the numbers from it so i put the old one back. Im just wondering if it can have something to do with the voltage. Thanks again

Im having a problem with my donkey kong and i was wondering if anyone could help. As im playing the game im losing the horisontal hold after a few minutes. Can this be a voltage issue or is it my monitor. Any help would be great. Thanks

Im looking for a upright in any condition! projects welcome

Hello all,

Just wanted to introduce myself, I'm john(aka ) I'm from new york city and I'm looking to get hooked up with the community around my area. Not many places to pick up games around here... So I'm looking to make friends with the community in the new york, jersey, Pennsylvania and new England areas.Thanks again and i look forward to the new friendships and discussion ill have thought this forum. 

John